برد کنترلر پرینتر سه بعدی 32 بیتی Ramps-FD سازگار با آردوینو Due

187,500 تومان
مدل کالا : Ramps-FD
کد کالا : 6270-5305
موجودی : درحال تامین موجودی (15الی21 روز)

مرور کلی

برد کنترلر پرینتر سه بعدی 32 بیتی Ramps-FD سازگار با آردوینو Dueمناسب برای ساخت انواع سی ان سی تا 6 محور (اکسترودر 3 رنگ) ، انواع  ربات های فوق پیچیده مهندسی ، پزشکی و آزمایشگاهی و ...ساخت ا...

برد کنترلر پرینتر سه بعدی 32 بیتی Ramps-FD سازگار با آردوینو Due

مناسب برای ساخت انواع سی ان سی تا 6 محور (اکسترودر 3 رنگ) ، انواع  ربات های فوق پیچیده مهندسی ، پزشکی و آزمایشگاهی و ...

ساخت انواع پرینتر های سه بعدی ، مخصوص پرینترهای سه بعدی full color (تمام رنگی!)

برای دریافت اطلاعات تکمیلی برد Ramps-FD به این لینک مراجعه نمایید.


Arduino Dueis the new Arduino board that is using an ARM Cortex M3 CPU.


The Atmel SAM3X8E chip used on the Due operates at 3.3V and is not compatible with 5V. Therefore the RAMPS shield will not work with Due, and worse applying 5V to the Due's inputs will likely damage the chip.


Therefore there are several possibilities:
create a new RAMPS variant which is compatible with the Due. Possibly could also be made backwards compatible with Mega.
create a RAMPS Interface Board (RIB) to sit between Due and RAMPS to perform level-shifting, and any other needed functions.


Why should i use Ramps-FD instead of Ramps1.4?
Campare Ramps-FD with Ramps1.4,the Improvements of Ramps-FD are below
The RAMPS-FD has other hardware protection, through the jumper cap control motor drive IC
The RAMPS-FD Much more than Ramps1.4 2-way PWM
The RAMPS-FD has Larger driving power than Ramps1.4
The RAMPS-FD 'POWER has two choices:12v and 24v


why should i selectArduino Due instead of Arduino Mega?
due has lower power ,computing faster and flash,sram bigger than mega2560
CPU operates at 3.3V
High-current IO pins are capable of 15 mA source, 9 mA sink
Low-current IO pins capable of 3 mA source, 6 mA sink
CPU package has an absolute max of 130mA
The Due has 1 dedicated SPI port, and 4 multipurpose USART/SPI ports. The SPI port is only routed to the 6 pin header used for ICSP on Mega, but this is not used for ICSP on Due.
The Due does not have any EEPROM


Hardware issues:
MOSFETs need to be compatible with threshold voltage of 3.3V or better have a gate driver which allows any MOSFET to be used
Expansion pins need to be level-translated, but this depends on how they are used
Add ons: SD card, thermocouple drivers, LCD boards
Is heat dissipation of Due ok with RAMPS shield over it?
Some opto-endstops need 5V power, and return 5V on signal
(AUX-3) The SPI pins on the Mega (mapped to pins D50-52) are not SPI pins on Due


Hardware features known to be compatible:
The Allegro stepper drivers will run with VDD = 3.3V and the logic signals compatible with 3.3V. This should apply to all the Pololu style drivers.
Servos "should" be able to operate with +5V power and a PWM signal of 3.3V
Thermistors will operate at 3.3V but the Analog Ref is also 3.3V, so no changes should be necessary
Mechanical endstops should be OK, if they do not use external pullup to 5


Add-on compatibility:
Sdramps (AUX-3 SPI connector) This board has a 5->3.3 voltage regulator and a level translator. I think it will work and be compatible if powered from 5V, but will not work if powered at 3.3V, because the input to the regulator is too low.

Possible improvements:
Move connectors near to board edge
Allow for latching or screw terminals?

Firmware changes:
Firmware needs to be compiled with ARM compiler (gcc)
Arduino libraries may be compatible
Any references to AVR CPU peripherals, AVR include files or AVR compiler features need to be ported
There is no EEPROM on the SAM3X.

1398/12/25 05:53:33

سلام
ماژول تبدیل LCD برای این برد رو موجود دارید؟ از کجا می تونیم تهیه کنیم؟

پاسخ:
با سلام
این برد سه مدل تبدیل LCDدارد، کدامیک مد نظر می باشد.
لطفا با واتس اپ و یا تلگرام 09371101055 در ارتباط باشید.

1398/04/28 14:30:11

شما تو توضیحات نوشتید برد ۳ رنگ است ولی تو یکی از عکس ها از ۶ رنگ استفاده شده. چطور میشه با ۳ اکسترودر از ۶ رنگ استفاده کرد ؟


پاسخ:
با سلام.
از دو برد به صورت موازی استفاده گردیده است.
جهت راهنمایی و چگونگی کار با واتس اپ و تلگرام 09371101055 در ارتباط باشید.

1398/02/01 13:03:31

سلام
خیلی کم کار شدید........


پاسخ:
با سلام.
ضمن پوزش ، تبعات خود تحریمی گمرک است.
در انتظار دستور العمل جدید گمرک برای سال 98 هستیم.

1397/03/04 14:06:08

سلام خسته نباشید ، من نظر هارو توی سایت های مختلف خوندم همه از مشکلات ورژن یک این برد دارن میگن ، ایا این بردی که گفتید نسخه 1.2 هست ، مشکلات نسخه ی 1 رو نداره ?!
خیالمون بابت خریدش راحت باشه ?!


پاسخ:
با سلام.
نسخه 1rev A می باشد.
علیرقم انتشار خبر تولید نسخه 2 ، خبری از پخش این نسخه نمی باشد.
با چند تغییر جزیی میتوانید همین نسخه رو استفاده کنید.
راهنمای تغییرات :
http://forums.reprap.org/read.php?219,424146
http://reprap.org/wiki/RAMPS-FD

1396/05/08 02:48:55

سلام
این برد ورژن چند هستش؟ ورژن 1 این برد مشکل سطح ولتاژ داره و به پورت های due صدمه میزنه.


پاسخ:
با سلام.
این برد V1.2 می باشد.در مورد نسخه یک مشکل سطح ولتاژ نبود، مشکل از عدم تطبیق فریم ور های موجود با چیدمان برد DUE بوده است که با قدری تغییر در کد قابل حل بوده است.
البته با توجه امکان عدم آگاهی دوستان به این امر نسخه یک تامین نشد.
در صورت استفاده از شیلد های سری FD لینک زیر را مطالعه فرمایید.
http://forums.reprap.org/read.php?219,424146

نظر بدهید

توجه: HTML ترجمه نمی شود!

امتیاز بد           خوب